Pre-lock Smith & Wesson Model 629-1 Above average condition with a minor handling mark on the left side of the revolver just below the cylinder. Leupold 4X ER scope with Leupold rings and base. 

For additional pictures or to purchase:https://www.israel-arms.com/S-W-629-1-8-3-8-barrel-p/n934387.htm

Specs:

.44 Magnum Caliber
8 3/8" Barrel
Stainless Steel
Factory Pachmayr Rubber Grips
Red Ramp Front Sight
Rear Sight replaced with a Leupold 4X Extended ER Scope
Leupold Scope Base
Manufactured 1982-1983

SPECS

The Smith & Wesson Model 29 is a six-shot, double-action revolver chambered for the .44 Magnum cartridge and manufactured by the United States company Smith & Wesson.

The Model 29 was offered with 3, 4, 5, 6, 612838 and 1058 inches (76, 102, 127, 152, 165, 213 and 270 mm) barrels as standard models. Other barrel lengths were available either by special order from Smith & Wesson's Custom Shop or custom-built by gunsmiths. The 5 inches (130 mm) barreled variant had a full-length underlug. Finish options available included a highly polished blued or nickel-plated surface.

At the time of its introduction, the Model 29 was the most powerful production handgun, although it was later overtaken by handguns chambered for the even larger .454 Casull and .50 Action Express cartridges. It was made famous worldwide by association with the fictional character "Dirty Harry" Callahan.

Design

The Model 29 will chamber and fire .44 Special cartridges, as the .44 Magnum was developed from the .44 Special. The Magnum case is slightly longer to prevent magnum rounds from being chambered and fired in handguns chambered for the .44 Special.

History

 
Smith & Wesson Model 29s, with 4-and-838-inch (100 and 210 mm) barrels
 
Smith and Wesson Mountain Gun circa 1995

Elmer Keith's achievements in maximizing the power and performance of the .44 Special was the inspiration and driving force behind the introduction of the .44 Magnum by Smith & Wesson. His intention for the new round was for it to be used in sidearms for hunters of large, dangerous game, rather than for self-defense, though with today's specialty cartridges, it can be a good defensive round.[1]

S&W's production of a large N-frame revolver in .44 Magnum began in 1955; the Model 29 designation was applied in 1957.[2]

At the time of its introduction, the Model 29 was the most powerful production handgun. There were a number of custom calibers that were more powerful, as in the old Howdah pistols of the 19th century.

It remained primarily the province of handgun enthusiasts, some law enforcement personnel and hunters until 1971 when Clint Eastwood made it famous as "the most powerful handgun in the world" in the movie Dirty Harry. After the movie's release, retailers had trouble keeping the Model 29 in stock.[3]

In the late 1990s, Smith & Wesson discontinued production of many models of revolvers, including the 'basic' Model 29; since then, at various times, the model, in limited or 'custom' configurations, has been manufactured in as many as 10 evolutions.[4]

Variants

 
Smith & Wesson Model 29-2

The original Model 29 was superseded by the Model 29-1 in 1960, with modifications made to the ejector-rod screw. The Model 29-2 replaced it the following year, with one screw that had secured the cylinder-stop spring being deleted. The barrel length was shortened from 612 to 6 inches (170 to 150 mm) in 1979. These two versions are known as "pinned and recessed". "Pinned" means that the barrels are screwed in, and secured by a pin driven through the frame and a notch in the barrel. "Recessed" denotes the rear of the bored cylinder holes being countersunk, so that, when loaded, the cartridge rims are fully enclosed by the cylinder. In 1982, the cost-cutting Model 29-3 dropped recessed cylinders and pinned barrels for crush-fit barrels.[2]

The -4 and -5, produced from 1988 and 1990 respectively had changes to improve durability for heavy use. In 1994 the 29-6 began production, now fitted as standard with rubber Monogrips from Hogue to replace the previous wooden items, standard tapped holes also being provided for attaching scope mounts. The 29-7 started production in 1998 with changes to the locking mechanism, the firing pin's attachment, and a hammer and trigger produced with a metal injection molding process.[2]